tygerfifteen
Ruckster
knobby tires,cdi, k/n filter,variators,rollers
Posts: 248
|
Post by tygerfifteen on Apr 2, 2005 6:44:13 GMT -5
just wondering if anybody has had problems after they have installed their cdi. just installed mine with the help of the instructions from battlescooter and now my signals won't work, the brake light and headlights work though.
|
|
|
Post by CTRukus on Apr 2, 2005 8:45:40 GMT -5
I haven't changed my CDI box yet. So, this might be a silly or stupid question:
Did you disconnect the wires or loosen them at all? they're all kind of grouped together on the left side of the battery box....There should be 2 green ones, one blue and one orange.
|
|
tygerfifteen
Ruckster
knobby tires,cdi, k/n filter,variators,rollers
Posts: 248
|
Post by tygerfifteen on Apr 2, 2005 19:38:14 GMT -5
well actually i changed the front turn signals lower to the reflective spots. and replaced the bracket on the brake light, replaced the brake light and put the back signals lower.
sooooo..... the brake light works perfectly , i checked signals none of them work but they are all connected right none are touching each other, but this just occured when i installed the cdi, but the scooter runs perfectly, ALSO the speddometer light doesn't work when the scooter is on but the head lights work.
any thoughts?
|
|
|
Post by chanito on Apr 2, 2005 23:53:56 GMT -5
Well we will have to do this, step by step, first we need to get to the turn signal relay, is a round thing by the batt, you need to take the 3 wire connector and jump the grey and black wires together, now turn the ignition on and try the turn signals, they should light up, they just won't blink, if they light up the the problem is the turn light relay, if the don't then they might be something else, and we need to get a test light or a volt meter. But first do this test and let us know, i will check this post and go from there
|
|
tygerfifteen
Ruckster
knobby tires,cdi, k/n filter,variators,rollers
Posts: 248
|
Post by tygerfifteen on Apr 3, 2005 0:37:52 GMT -5
problem solved, didn't know that the sister wires (geen/red, etc had to be connected to the original wires) lol everything works but............ i can only tell an improvement in acceleration, lots of improvement nothing with the top speed , doesn't even pass 60Km...hmmmmmmmmm
|
|
|
Post by Dandy Dan on Apr 3, 2005 10:35:17 GMT -5
i can only tell an improvement in acceleration, lots of improvement nothing with the top speed , doesn't even pass 60Km...hmmmmmmmmm \ I'd bet my grandmother it's your valve shims or your main carb jet if you've been playing with the carb.
|
|
|
Post by zoomerman on Apr 20, 2005 23:25:22 GMT -5
i can only tell an improvement in acceleration, lots of improvement nothing with the top speed , doesn't even pass 60Km...hmmmmmmmmm Could you tell me how much acceleration difference you notice ? Such as: If a stock Ruckus's acceleration is a 5 out of 10 would yours be now a 6 or ?...
|
|
Doctavius
Ruckster
Supah Sharp Shootah!!!
Posts: 220
|
Post by Doctavius on Apr 23, 2005 1:05:53 GMT -5
How does it do when you open it up on a downhill?.... Also have you noticed the difference when going uphill?.... with mine I don't de-cellerate as much as it would stock.
|
|
|
Post by abe on Apr 23, 2005 8:24:11 GMT -5
This thread is way out of control. Move your different topics some place else please
|
|